Laserfiche WebLink
• Each locker shall have at least one smart card reader per pair of adjacent doors. <br />• Each smart card reader shall have a dynamic display of real time rental status and usage rules. <br />• Lockers shall be of a modular design that allows for easy replacement of components such as doors, top and side panels, <br />electronic controllers, and latching mechanisms. <br />• Locker battery power supplies shall use dual redundant battery packs, and advanced battery selection logic to allow run times <br />over one year per pack under normal conditions. Packs shall utilize readily available Alkaline, Lithium, or NiMh cells that are <br />easily replaced and cost-effective to maintain. <br />• Alternate power supply configurations shall include {haKI-wir-ed420VAC with alkaline -ba# VAC—wi#k► <br />alkaline battery ba #h a1 redundant aikaii <br />pac-I-seleetican-log--to-deplete-the--p ' ing te-tie-resefve-pack,-wac , 4 -refuse <br />th packs have been-depleted},-er4Solar power with rechargeable low self -discharge NiMh and alkaline battery <br />backup]. <br />• Lockers shall be capable of operation in temperatures ranging from 0-110°F. <br />• Lockers shall be capable of operating in exposed conditions and in coastal marine environments. <br />• Lockers shall restrict the entry of wind-blown debris around their full perimeter. <br />• Lockers shall have adjustable system for anchoring and leveling on site with adjustment range of up to 3.0% slope. <br />• Lockers shall provide access for easy removal or cut-off of installed anchors, to facilitate Locker relocation. <br />• Four -space Lockers shall be of an aspect ratio which resists lifting and tipping, and shall be capable of operating when <br />unanchored: <br />• Lockers shall be capable of being installed on concrete substrates. <br />• Lockers shall provide standard externally mounted number plates made of a durable, weather resistant material, and shall <br />include electronically coded controller, location, and Owner ID numbers which are logged on every transaction. <br />• Lockers shall have no exposed fasteners that would enable locker disassembly from the outside. <br />• Locker shall have external finishes which facilitate the removal of graffiti. <br />Locker Materials: <br />• Locker doors shall be fabricated from 16 -gage 304 stainless steel fully perforated with a %-inch on 3/8 -inch staggered, round - <br />hole pattern. Doors shall have interior reinforcement to reduce warping increase out -of -plane stiffness. Doors shall be at least <br />1.5" thick to resist prying attacks. <br />• No portion of door shall displace more than 0.4" when subjected to prying at any location on the door using a 30 Ib force on a <br />36" pry bar with a 1" fulcrum. <br />• Exterior Locker frame components shall be precision manufactured sheet steel of no less than 16 -gage 304 stainless steel. <br />• Locker roofs shall be high -durability FRP with additives for fire resistance, and shall use a UV -resistant resin. Locker roofs shall <br />have at least 20% translucency to aid in visibility of contents. <br />• Locker roofs shall be crowned to enable proper water run-off, and roof system shall be capable of resisting the dropping of a <br />2001b load from 12 inches without any permanent buckling, cracking, or deformation of the roof or other locker components. <br />• Locker sides and doors shall be capable of resisting the impact of a 1001b pendulum swinging from a height of 5 inches above <br />the impact point without any permanent buckling, cracking, or deformation of the doors, side panels, or other locker <br />components. <br />• The latching device shall be capable of resisting a 3000lb pull-out force, such as during an attempt to pry the door open. <br />• Locker interior divider panels shall be G90 hot -dipped galvanized material with 50-70% open area. <br />• Locker exterior side panels shall be %-inch on 3/8 -inch staggered, round -hole, fully perforated panels of no less than 18-guage <br />304 stainless steel. <br />• Locker materials shall allow maximum visual transparency for ease of locker inspection. <br />• User interface display and solar windows shall be protected by 1/4" thick polycarbonate with abrasion and UV resistance <br />properties, "Makrolon 15" or equal. <br />Finish: <br />• External locker hardware (such as nuts, bolts, and latches) shall be 18-8 stainless steel, or better. <br />Contact us at (510) 549-2853 or sales@elocktech.com Copyright © 2013 eLock Technologies LLC <br />Page 2 of 3 <br />