Laserfiche WebLink
PowPako Dimming Module Energi TriPako Series Wireless Lighting Control <br />Specifications (continued) <br />Key Design Features <br />• LED status indicator shows load status and provides <br />programming feedback <br />• Configurable high-end and low-end trim <br />• Power failure memory: If power is interrupted, <br />connected loads will return to the previous level prior <br />to interruption <br />• 0-10 V control miswire protection up to 30 V= <br />• Programming lockout can be enabled for public <br />spaces <br />• 0-10 V control can be programmed to be inverted <br />for 10-0 V control <br />• Daylight override: Pressing the raise button on an <br />associated Picoo wireless control will temporarily <br />override daylighting for all fixtures wired to the <br />PowPako Dimming Module with 0-10 V control <br />- Daylighting will be re -enabled for all the fixtures <br />wired to the PowPako Dimming Module with <br />0-10 V control when one of the following occurs: <br />• Two hours have passed since the override.* <br />• ON, OFF or Preset button has been pressed on <br />a Pico® wireless device controlling the fixtures <br />wired to the PowPak® Dimming Module with <br />0-10 V control. <br />• All associated Occupancy Sensors have <br />reported unoccupied. <br />Each time a daylighting override occurs for any control associated <br />to the PowPako Dimming Module with 0-10 V control, the <br />two-hou r timer is reset, <br />Advanced Configurations <br />Picoo Wireless Controls <br />• Up to nine Picoo wireless controls <br />• Favorite levels can be set for each Pico® wireless <br />control <br />Radio Powr SavrTM Daylight Sensor <br />• The Radio Powr SavrTM daylight sensor will affect all <br />connected ballast and LED drivers equally <br />• For multple rows of daylighting, a separate PowPako <br />Dimming Module with 0-10 V must be used for each <br />daylighting row <br />LUTRON. SPECIFICATION SUBMITTAL <br />Job Name: <br />Job Number: <br />Model Numbers: <br />369779b 3 10,30,2014 <br />Minimum Light Level Setting (optional) <br />• Certain applications, such as hallways, may require <br />that the lights never turn off. For these areas, select <br />the minimum light level option and the load will lower <br />to programed low-end level. Default operation lowers <br />to OFF. <br />High- and Low -End Trim <br />• High-end and low-end trim affect all connected <br />fixtures equally, and can be configured from <br />the PowPak® Dimming Module or from any <br />associated Pico® wireless control when unit is not in <br />programming lock -out mode <br />• Adjustable low-end trim (0-45%). Trimmable <br />low-end can ensure a stable light level. Some fixtures <br />will flicker or drop out if trimmed too low. <br />• The maximum light output of connected fixtures can <br />be decreased down to 55% for energy savings in <br />over -lit spaces <br />Note: The perceived light output of low-end trim may <br />vary between fixture manufacturers and model <br />numbers. For best results, do not mix different <br />ballasts or drivers on the same 0-10 V circuit. <br />Radio Powr SavrTM Occupancy Sensors <br />• Radio Powr SavrTM occupancy and vacancy sensors <br />control all connected ballasts or drivers <br />• Picoo wireless controls can be used to adjust the <br />Occupied levels of fixtures that they control from <br />1 % to 100°% (of output signal) or can make them <br />unaffected by Occupancy events <br />• Vacancy events (area becomes unoccupied) turn all <br />ballasts and driver models off or to minimum light <br />level <br />Programming Lockout <br />• Once enabled, all Pico® wireless controls can no <br />longer perform programming or set favorite levels <br />• To change settings, programming lockout must be <br />unlocked by a button combination directly on the <br />PowPako Dimming Module. <br />Page <br />