Agmt 2015 eLock Technologies LLC

Home

• Each locker shall have at least one smart card reader per pair of adjacent doors. • Each smart card reader shall have a dynamic display of real time rental status and usage rules. • Lockers shall be of a modular design that allows for easy replacement of components such as doors,top and side panels, electronic controllers,and latching mechanisms. • Locker battery power supplies shall use dual redundant battery packs,and advanced battery selection logic to allow run times over one year per pack under normal conditions. Packs shall utilize readily available Alkaline, Lithium,or NiMh cells that are easily replaced and cost-effective to maintain. • Alternate power supply configurations shall include -. :- • -: • ' -- ' --- :: . • -- - ---- --- - -- - : Solar power with rechargeable low self-discharge NiMh and alkaline battery backup]. • Lockers shall be capable of operation in temperatures ranging from 0-110°F. • Lockers shall be capable of operating in exposed conditions and in coastal marine environments. • Lockers shall restrict the entry of wind-blown debris around their full perimeter. • Lockers shall have adjustable system for anchoring and leveling on site with adjustment range of up to 3.0%slope. • Lockers shall provide access for easy removal or cut-off of installed anchors,to facilitate Locker relocation. • Four-space Lockers shall be of an aspect ratio which resists lifting and tipping,and shall be capable of operating when unanchored. • Lockers shall be capable of being installed on concrete substrates. • Lockers shall provide standard externally mounted number plates made of a durable,weather resistant material,and shall include electronically coded controller, location,and Owner ID numbers which are logged on every transaction. • Lockers shall have no exposed fasteners that would enable locker disassembly from the outside. • Locker shall have external finishes which facilitate the removal of graffiti. Locker Materials: • Locker doors shall be fabricated from 16-gage 304 stainless steel fully perforated with a'''A-inch on 3/8-inch staggered,round- hole pattern. Doors shall have interior reinforcement to reduce warping increase out-of-plane stiffness. Doors shall be at least 1.5"thick to resist prying attacks. • No portion of door shall displace more than 0.4"when subjected to prying at any location on the door using a 30 lb force on a 36"pry bar with a 1"fulcrum. • Exterior Locker frame components shall be precision manufactured sheet steel of no less than 16-gage 304 stainless steel. • Locker roofs shall be high-durability FRP with additives for fire resistance,and shall use a UV-resistant resin. Locker roofs shall have at least 20%translucency to aid in visibility of contents. • Locker roofs shall be crowned to enable proper water run-off,and roof system shall be capable of resisting the dropping of a 200lb load from 12 inches without any permanent buckling,cracking,or deformation of the roof or other locker components. • Locker sides and doors shall be capable of resisting the impact of a 100lb pendulum swinging from a height of 5 inches above the impact point without any permanent buckling,cracking,or deformation of the doors,side panels,or other locker components. • The latching device shall be capable of resisting a 30001b pull-out force,such as during an attempt to pry the door open. • Locker interior divider panels shall be G90 hot-dipped galvanized material with 50-70%open area. • Locker exterior side panels shall be'''A-inch on 3/8-inch staggered,round-hole,fully perforated panels of no less than 18-guage 304 stainless steel. • Locker materials shall allow maximum visual transparency for ease of locker inspection. • User interface display and solar windows shall be protected by 1/4"thick polycarbonate with abrasion and UV resistance properties,"Makrolon 15"or equal. Finish: • External locker hardware(such as nuts,bolts,and latches)shall be 18-8 stainless steel,or better. Contact us at(510)549-2853 or sales@elocktech.com Copyright©2013 eLock Technologies LLC Page 2 of 3