Laserfiche WebLink
angle of departure. <br />PROTECTIVE RAILS <br />The upper body area shall be protected with radius corner 1" diameter aluminum tube railing assembly installed around the <br />top of the body. The corners of the body shall have vertical risers space in critical areas. The railings shall act as protection <br />for the upper body structures when off road in heavy brush conditions. The rear upper body corner rails shall house the <br />upper emergency lights and work lights. <br />REAR VERTICAL RAILS TO BE WIDENED, TURNING DOWNWARD JUST INSIDE INBD WALL OF COMPARTMENTS <br />SIDE BODY COMPARTMENTS, FRONT BODY -- DRIVER AND PASSENGER'S SIDES <br />Two (2) body equipment storage compartments shall be installed at the front of the body just behind the headache rack, one <br />each side of the apparatus. The dimensions shall be approximately: 30" wide, 44" high, and 24" deep. The compartments <br />shall be constructed of .125" aluminum tread plate on all exterior surfaces. Each compartment shall be equipped with a <br />vertically hinged door with a single latch installed. The doors shall be equipped with gas operated door opening assistant <br />cylinders. <br />Each vertical compartment shall have one (1) fixed shelf. <br />The compartment floors shall be lined with turtle tile. <br />596632.2 - TULIP CLIPS <br />Two (2) small tulip clips shall be installed on aluminum brackets at the rear of the bed, one (1) each side, below the side <br />facing Rigid lights. See picture. <br />100121.1 - ANGLED CORNERS, FLAT-BED <br />The front corners of the flat-bed body will be angled at approximately 45 degrees. <br />100437.4 - FRONT BODY TRANSVERSE COMPARTMENT <br />A transverse compartment 15"W x 24"H x 96"L will be installed in front of the water tank. The compartment shall be lined <br />with turtle tile. <br />100144.3 - DRIVERS SIDE UPPER BODY COMPARTMENT <br />A body equipment storage compartment shall be installed on the flatbed surface, driver's side of the apparatus. The exterior <br />dimensions shall be approximately 55" wide, 24" high, and 18" deep. The compartment shall be constructed of .125" <br />aluminum tread plate on all exterior surfaces. The compartment shall be equipped with a lift up door with latch installed. The <br />door shall be equipped with dual gas operated door opening assistant cylinders. Turtle tile shall be installed on the floor. <br />A second compartment shall be installed aft of the above. The dimensions shall be 22"W x 24"H x 18" D. Materials shall be <br />the same as above. <br />The actual door openings shall be approximately 3" smaller in dimension. <br />100148.2 - PASSENGERS SIDE UPPER BODY COMPARTMENT <br />A body equipment storage compartment shall be installed on the flatbed surface, passenger's side of the apparatus. The <br />exterior dimensions shall be approximately 55" wide, 24" high, and 18" deep. The compartment shall be constructed of <br />.125" aluminum tread plate on all exterior surfaces. The compartment shall be equipped with a lift up door with latch <br />installed. The door shall be equipped with dual gas operated door opening assistant cylinders. Turtle tile shall be installed on <br />the floor. <br />A second compartment shall be installed aft of the above. The dimensions shall be 22"W x 24"H x 18"D. Materials and <br />construction shall be the same as above. <br />The actual door opening shall be approximately 3" smaller in dimension. <br />100585.1 - UNDER BODY COMPARTMENTS -- REAR BODY, D/S AND P/S <br />Two (2) under flat bed equipment storage compartments shall be installed under the flatbed surface, on the passenger's and <br />driver's side of the apparatus, behind the rear axle. The exterior dimensions shall be approximately: 20" wide, 15" high, and <br />23" deep. The compartments shall be constructed of .125" aluminum on all exterior surfaces. The compartments shall be <br />equipped with a vertically hinged door with latch installed. The compartment shall have turtle tile installed. <br />Skeeter Brush Trucks Page 12 12/03/2020137