Laserfiche WebLink
100159.5 - UNDER BODY COMPARTMENT -- REAR CENTER <br />An under body equipment storage compartment shall be installed under the flatbed surface located in the center rear of the <br />apparatus. The dimensions shall be approximately: 33" wide, 6" high, and 108" front to rear. The compartment shall be for <br />by the vertical body beams, upper floor surface, and an aluminum lower floor area. The compartment shall be equipped with <br />a hinged drop down door with dual latches installed. <br />SHALL HAVE TWO (2) DIVIDERS ON P/S FOR HARD SUCTION <br />100166.3 - REAR SLIDE-OUT TRAY <br />The rear center compartment shall be equipped with an .190" aluminum slide out tray on UHMW plastic slide pads. The tray <br />shall be full width and full length of the compartment interior. <br />100160.2 - INTERIOR COMPARTMENT VENTILATION LOUVERS <br />The interiors of the compartments shall be provided with louvered ventilation units. <br />100161.1 - COMPARTMENT DOOR KEY LOCKS <br />The hinged compartment doors shall be equipped with key type door locks. <br />100425.3 - COMPARTMENT LIGHTING, STRIP LIGHTS <br />Each upper body compartment shall be equipped with RED 40" LED strip light, installed on the upper side of the door <br />opening. <br />100163.1 - AUTOMATIC COMPARTMENT DOOR LIGHT SWITCHES <br />Each exterior compartment light shall be automatically controlled by a door activated switch. <br />100164.3 - DOOR AJAR LIGHT <br />A "door ajar" or equipment operation warning light shall be installed on cab dash. The light shall be flashing BLUE LED light <br />with a clear lens. <br />596646.3 - STOKES BASKET STORAGE <br />There shall be provisions to store a CMC 726112 (see hyperlink) on top of the body. It shall be installed inside the transverse <br />compartment. The exact design shall be determined at the pre-construct conference. More <br />100169.5 - HOSE TRAY -- DRIVERS SIDE <br />A hose storage tray shall be installed over the driver's side equipment compartment, on the driver's side of the apparatus. <br />The dimensions shall be approximately: 16" wide, 12" high, and 72" long. The hose tray shall be constructed entirely of .125" <br />aluminum tread plate on all exterior surfaces. The assembly shall be equipped with a hinged lift up aluminum tread plate <br />door on top, enclosed front panel, and open rear area. The hose tray shall be equipped with Turtle Tile floor covering. <br />100172.5 - HOSE TRAY -- PASSENGERS SIDE <br />A hose storage tray shall be installed over the passenger's side equipment compartment, on the passenger's side of the <br />apparatus. The dimensions shall be approximately: 72" long, 16" wide, and 12" high. The hose tray shall be constructed <br />entirely of .125" aluminum tread plate on all exterior surfaces. The assembly shall be equipped with a hinged lift up <br />aluminum tread plate door on top, enclosed front panel, and open rear area. The hose tray shall be equipped with Turtle Tile <br />floor covering. <br />100180.3 - REAR PULL OUT STEP (Qty: 2) <br />There shall be a rear "Pull-Out-Fold-Down" step located at the rear of the apparatus, step shall be stowed in a pocket under <br />the rear of the unit. Storage pocket shall be fabricated to allow easy access to deploying for operation. <br />There shall be two (2) body access steps located at the front corners of the body, one (1) each side. <br />100181.2 - FOLDING STEP <br />A Signature 4 lighted 8" square folding step of die cast zinc shall be installed. The step shall comply with NFPA non-slip <br />standards and shall be installed on the rear driver's side of the body. The step shall be equipped with lighting to NFPA <br />standard. <br />Skeeter Brush Trucks Page 13 12/03/2020138