Laserfiche WebLink
100327.1 - ELECTRICAL HARNESS AND WIRING <br />All wiring shall be hidden, enclosed, or protected under the body in protective material, or within the apparatus body <br />components. In addition, split loom conduits shall be installed and enclosed, suitably secured and protected against heat and <br />physical damage. <br />100090.2 - BATTERY MASTER DISCONNECT <br />A battery disconnect system shall be installed to control the 12 volt power supply from the battery system to the body and <br />cab final stage manufacturer installed equipment. The solenoid shall be controlled by the standard key starter switch. <br />THE FIRE PUMP WILL HAVE LIVE PUMP WIRING TO ALLOW THE FIRE PUMP TO OPERATE WHEN THE CHASSIS IS TURNED OFF. <br />100094.10 - BATTERY CHARGER AND120 VOLT SHORE POWER RECEPTACLE <br />A Kussmaul Autocharge 1000 model #091-215-12-194B, high output automatic battery charger shall be provided. The <br />battery charger shall be wired to the 12 volt battery system. The unit shall be mounted in a clean, dry area accessible for <br />service and/or maintenance. It shall be wired to the specified shore power receptacle. <br />It shall include a 091-194-IND Digital Status Display Center. <br />It shall also include a 091-55-15-120 15 amp "auto-eject" shore power receptacle with hinged weatherproof cover and an <br />enclosure for protection from dirt and damage. The shore power plug shall be "ejected" when the chassis' engine starter is <br />engaged and the receptacle shall be wired to any 120 volt A/C equipment requiring shore power. <br />Location shall be: rear body panel, driver's side, below M7, DISPLAY ABOVE AUTO-EJECT <br />CHARGER TO ME MOUNTED IN REAR CREW CAB AREA UNDER BENCH SEAT <br />100328.1 - DOT IDENTIFICATION LIGHTS <br />All LED identification lights shall be installed on the vehicle as required by applicable highway regulations. <br />100329.1 - LICENSE PLATE MOUNTING <br />An LED license plate light shall be installed on the rear vertical wall of the body. <br />100330.2 - BRAKE, TURN, TAIL LIGHTS <br />Two (2) Whelen M6 Series Model M6BTT 4-5/16" x 6-3/4" brake, turn, tail lights with M6FC chrome flanges shall be provided. <br />The warning lights shall incorporate Linear Super-LED and Smart LED technology. The lighthead configuration shall consist of <br />18 red Super-LEDs and a clear optic polycarbonate lens. The lightheads shall be surface mountable via two screws. <br />The lightheads shall utilize optic collimators and chrome vacuum metalized reflectors for maximum illumination. The <br />lighthead shall include 164 flash patterns including: a variety of CA Title 13 compliant, sinkable, left/right, top/bottom, in/out, <br />and steady burn. The lightheads shall have the Whelen exclusive NERM (Non-Emergency Recognition Mode) feature. <br />The lens/reflector assembly shall be wet sealed and resistant to: water, moisture, dust, and other environmental conditions. <br />The outer lens shall have a hard coating applied to increases strength and ensure longevity. The light engine shall be <br />installed at the rear of the unit and be completely sealed. The pc board shall be conformal coated for additional protection. <br />The lights shall be furnished with five 6" wire pigtails, a Santoprene rubber gasket and the #M6FC chrome flanges shall be <br />included for installation. <br />100331.1 - BACK-UP LIGHTS <br />Two (2) Whelen M-Series, 4" x 6" rear LED back-up lights shall be installed. <br />100096.1 - TRAILER PLUG <br />Wiring shall be provided at the rear of the apparatus for the towing of an auxiliary trailer. A 12 volt seven (7) pin electrical <br />connector shall be wired to the chassis stop, running, and turn lights. <br />100067.1 - OFF ROAD LIGHTS <br />No off road lights shall be installed. <br />Skeeter Brush Trucks Page 15 12/03/2020140